Fabio0716. 1130 posts · Joined 2015. #5 · Jun 11, 2018. If you are talking about the Passenger Motor mount. Official torque specs are. Nuts (engine) : 80nm or exactly 59 Ft-lbs. Bolts to frame : 90nm or 66 Ft-lbs. Here is the reference for that, straight from ford. Sent from my SM-G950U using Tapatalk. Hi all, My clutch has started slipping so will be replacing it along with the flywheel this weekend. Using ford genuine parts and have new flywheel bolts also. Would anyone know what torque settings the clutch and flywheel bolts need to be or does anyone have a link to or screens of the my Haynes manual say driveshaft bolt ..stage 145nm.stage 2angle tighten a further 90 degree..bolt are not to be re-use it say.. so you probably need to buy new bolt. This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.

How To Install / Replace a front control arm on a Ford Focus, the model years include 1998-2010. I will show you step by step on how to do this job. It can b

159 posts · Joined 2011. #3 · Jan 30, 2015. Yeah I had the torque mount off a few weeks ago to get to the gearbox filler. Just tightened it up with a 1/2" and it's fine. Can understand on things like wheel nuts, driveshaft bolts etc.. but torque mount it haha. Torque wheel speed sensor to knuckle to 133 in. lbs. e. Torque stabilizer bar upper link to 111 ft. lbs. f. Torque previously removed hub nut to 258 ft. lbs; to seat halfshaft. g. Torque new hub nut to 258 ft. lbs. h. 3617 posts · Joined 2019. #2 · Jun 6, 2021. Ask the guys over on focusst.org they seem to have pretty much all the info you will need for any job on the mk3, its an American site. chucknorris Discussion starter. 27 posts · Joined 2018. #3 · Jun 8, 2021. Was hoping id get the info from here. Important! Replacement: brake caliper – Ford Focus MK2. Check the brake fluid level in the reservoir and top up if necessary. Without starting the engine, press the brake pedal several times until you feel significant resistance. WELL DONE! AUTODOC recommends: Replacement: brake caliper – Ford Focus MK2. AUTODOC recommends: A question then: when re-using the caliper bolts, is the procedure still as if it was a new (TTY) bolt, which in this case is: torque to 85 lb ft and then turn the bolt a further 90 degrees? This makes me nervous as the torque for the near identical brembos on my Subaru is 80 lb ft with no additional angle.

4 posts · Joined 2005. #1 · May 27, 2005. Hey, Two quick questions? What is the torque setting for the cam bolt that connects and holds the cam gear in place??? Can't find it anywhere? ~40-45 ft/lbs. Anybody know any dyno tune places in San Diego other than the dyno shop in santee? Cheaper than $200 for a gear tune? Thanks.

Following my pre-MOT checks, where I detected some play in the lower ball joint, I am replacing the driver side front lower wishbone. A job that isn’t compli .
  • 393u65ub7r.pages.dev/319
  • 393u65ub7r.pages.dev/86
  • 393u65ub7r.pages.dev/179
  • 393u65ub7r.pages.dev/284
  • 393u65ub7r.pages.dev/115
  • 393u65ub7r.pages.dev/406
  • 393u65ub7r.pages.dev/25
  • 393u65ub7r.pages.dev/473

    • ford focus mk2 torque settings